Bathtub refinishing near me Lakeside CA

Are you looking for Bathtub refinishing in Lakeside CA? SB Refinishers is your local solution Call us today for a FREE consultation  (619) 781-8949


You can probably say this about lots of things, but bathtubs–they simply don’t make ‘em like they used to. Bathrooms were constructed around them. These tubs were considerably fuller and consequently more inviting compared to the baths you had see now. The dominant colour for tubs is white which is nearly the only method to really go.
With the 60s and 70s arrived the investigation of bathroom fixtures in pastels, browns, beige, and the like. Despite these bad choices, bathtubs in this era were still very well made. While building transferred to contain lightweights like acrylic, baths in steel seemed, and like the cast irons, these steel baths were elegant and even sometimes sculptural in layout.

Cast iron is usually heralded for its indestructibility when rust might set in. It has a close relative in steel, in fact one would turn into the other. Cast iron is heavier, while steel is heavy, and bathtubs made of these alloys ultimately well beyond their finish.

Learn more about:SB Refinishers – we cover your needs in Lakeside CA.

For just these reasons, you might choose to refinish a bath. Any type of bath may be refinished while those with a timeless clawfoot refinish hope to achieve a vintage feel. This article focus on the redo of an alcove tub, definitely the most often installed bathtub.

Tools Stuff Skill Level Estimated Time

• Acid-Based commercial cleaner Innovative 4 to 8 Hours
Acid etching paste
Baking soda
• Shop Vac • Plastic sheeting
Builders paper
Masking tape
• Auto polisher/buffer •
Polish pads and • Buffing • Sandpaper
Sailcloth drop cloth

• Rags and towels • Two-Part fiberglass repair putty
• Paper or store towels • Tack cloth
• Little blending trough •
Specialty acrylic urethane OR acrylic aliphatic polyurethane OR white paint and high gloss polyurethane
• Electrical paint sprayer • Denatured alcohol
• Caulk gun • Silicone caulk
Plumbing tools that are •
Tub Refinishing Factors
Off Site or In Place?
Cast iron and steel tubs are incredibly heavy, as mentioned above, and you’ll need at least three, a hand, deliver and to safely remove them to a refinishing works. In the case of an alcove bathtub, one that is “built-in,” it is typically best to approach it while it is still in place.
A refinishing works may often begin with a process called “dunking” or stripping the original finish. Once stripped, your bath may have a porcelain enamel used before it’s finally re-fired in a kiln. Comparable coatings can be implemented onsite; stripping, nevertheless, is replaced with other way of homework.

Will You Replace Hardware?

Working under the premise that once (re)concluded, you’ll have a new look bath. It might be worth it to plan for an upgrade of the tub’s present drain hardware.
It should be pointed out, too, that the borders are typically the “poorest” part of any finish. In a place constantly subjected to water, prior to applying your new bathtub finish, it makes sense at minimum to eliminate the drain.

Note: Access to the lower wall cavity supporting the bath drain is necessary at a minimum when upgrading a bathtub’s drain assembly.

Need help with Bathtub refinishing? SB Refinishers provides you with the highest quality services for your needs.

Contemplate How You’ll VentilateBecause, usually, you’ll be working with caustic substances and airborne paints, make sure that you’ve got sufficient venting as you work. Along with running a built in bath fan, it may additionally make sense to open a window and use cross-ventilation by placing a fan in an opposing doorway. Ventilation equipment may also be leased at home improvement stores or rental centers if additional concerns persist around your ability to work safely or apply paint efficiently.
Prepare the Job

There are numerous approaches available for effectively preparing a bath refinish. Irrespective of the approach you decide on, take great care during this phase. The steps below are common to any job training approach you might choose:
1) Remove Present Caulk: Remove caulk that should be contacting the tub surface. Start by cutting both the top and bottom edges of the caulk bead using a utility knife. Fully remove all existing caulk. Sweep out or vacuum up any debris that’ll make its way to the underparts of the the tub.

2) Remove OR Conceal the Overflow Plate: Plan to replace existing bath hardware. The bath’s drain continues to be in excellent working order, as well as if this really is not attainable, remove the tub’s overflow plate. If you opt to remove a connected lever, be conscious not to enable linkages to fall back in the overflow or drain.

3) Remove Drain Pop Up, Strainer Assembly, OR Mask: Remove as many of the open finished drain parts as possible. Mask any finished surface that you just select not to remove. Poke holes or make an X in masking tape to allow for drainage of water as it will be used much later in the prep period.

4) Give the Tub an Industrial Cleaning: Using an acid-based cleanser, spray down the entire tub surface. Allow the product sit for five full minutes and make use of a stiff-bristled brush to scrub away spots. Because these cleaners are caustic, wear rubber gloves (or better) and a correctly rated respirator. Then allow the bath dry.

Mask both the inside of the bath in addition to the face (or apron) of the bathtub as it intersects with bathroom walls. As it meets the floor, do the same with the bath. Cut holes in places where faucet or tub spouts handles may appear. Prior to spraying, use masking tape.

6) Mask Bath Spout and Faucet Handles: While you may require to time this with the other measures below, wrap bathtub spouts and faucets with contractor’s paper or added plastic (cling wrap will function just as well). Instead, it may make sense just to remove them.

Prepare the Surface and Also Make Small Repairs

Apply an Acid Etching Paste
Use a stiff-bristled four inch stain a scrub brush or brush to employ an acid etch designed specifically for porcelain. Cover the surface of the bath completely and let about 15 minutes for this product to do its thing. Wear rubber gloves (or better) and a properly rated respirator. Remove with a (clean) scrub brush and wash down the drain with bath water. Wipe dry with shop towels.
Alternatives for Acid Etching

Some will forgo acid etching in favor of using a bonding agent only. Others may use mechanical means to rough up the tub surface. While this approach is somewhat aggressive, most finishing products are self-leveling to the degree that they’ll level out pretty over a “ scarified” surface.
Fixing Bath Surface Imperfections

Spots and grittiness can appear on tub surfaces after decades of improper cleaning. Bleach and abrasive cleaners might be detrimental to tub surfaces, themselves working to etch porcelain. Green spots or rust could be addressed using oxalic acid mixed in hot water with talc to form a paste that was whiting.
Chips or dings must also be addressed prior to applying a finish. Blend of two -part fiberglass repair putty and apply to the affected area by means of a plastic spreader. Allow to dry based on the product’s directions and sand first with 36-grit sandpaper (the sort used for sanding floors) and then follow with an 80-grit paper to feather out the repair.

Follow with polyester or porcelain glazing to fill in little pockets which could show up in the repaired area if necessary.

Wipe Down

Wipe down the bath with paper towels first and follow with a tack cloth.
Discretionary: For a more thorough cleaning, give one final wipe to the bathtub with accelerated-evaporating denatured alcohol.

Caution: If acids either were not used, only use or have been effectively neutralized.

Applying Finishes: DIY Strategy

Refinishing Kits
That is a seemingly countless array of refinishing kits accessible from reputable manufacturers. The products vary broadly from epoxies to acrylics, spray-on to brush-on and even to roll-on alternatives. Generally speaking, you’ll find varying degrees of quality and dry times with these products. Do your homework before buying and comprehend that effectiveness may be informed by price with time. Select a reputable name and follow all directions closely. These kits should give a finish lasting one to five years with appropriate attention.
Construct Your Very Own Clothing

Brush on a suitable bonding agent,or spray on an appropriate primer using an airless (sub HVLP) paint sprayer (available for lease at local home improvement stores or rental facilities). The topcoat is implemented using the same sprayer (make sure to wash it thoroughly between steps). Hold the gun about six inches from the surface, when spraying. As you move back and forth work using long strokes along with a continuous movement, overlapping somewhat. Play about with a mixture of white paint and high-gloss polyurethane. Instead, spray or roll on a two-component marine epoxy. This process should afford a finish that can last between 3 and 10 years, if you haven’t skimped on homework.
Using Finishes: Pro Approach

Professional refinishers are plentiful, but be warned: the products and techniques used plus their opinions vary widely. It may not be surprising that lots of professional refinishers started out in trades like auto body repair, where work is often personalized.
Pro Techniques

Acrylic urethane enamel, acrylic aliphatic polyurethane, or an epoxy-based finish is applied in multiple layers using a paint sprayer. (There is much debate online about the favorite sprayer type for this particular job.n general, pick airless and HVLP through others.) Determined by the product used, each coat should dry 15 to 20 minutes before the following is employed. The concluding layer should dry for no significantly less than an hour.
An automobile compound buffed into the surface using an auto polisher and annular buffing pads is used by some. Added buffing is usually done by hand. Glazing may also be applied with a soft cloth to bring up a dazzling luster.

Tear Down and Reinstall Fixtures
In case any of the newly applied finish begins to pull away with masking, it’s a good idea to work with a utility knife in hand. Work with care over the just finished surface. Bundle waste into construction bags and dispose of appropriately.
It’s frequently better left to a pro, while bathtub refinishing can certainly be a DIY project. SB Refinishers in San Diego bathtub refinishing is simply one of the most nearly priced jobs. Prices typically range from $400 to $500 and are usually packaged with a warranty that is significant.
The most important factor in hiring a professional for this particular occupation is the individual technician scheduled to do the work. That’s right, don’t necessarily hire a professional based on the reputation of the firm, on their system, or on their procedure, but rather on the authentic individual you would need doing your job. These mechanics should be able to generate a portfolio of work and references. Request it and review it before making the decision.

bathtub reglazing San Diego



[su_tabs active=”3″][su_tab title=”Refinishing Videos”][su_tabs active=”3″][su_tab title=”Refinishing Videos”][/su_tab] [/su_tabs][/su_tab] [/su_tabs]

Leave a Reply

Your email address will not be published. Required fields are marked *