Bathtub refinishing near me La Jolla California

Are you looking for Bathtub refinishing in La Jolla California? SB Refinishers is your local solution Call us today for a FREE consultation  (619) 781-8949


You can probably say this about a lot of matters, but bathtubs–they only don’t make ‘em like they used to. For the larger part of the past century, bathtubs were formed from cast iron and coated with porcelain enamel. Bathrooms were built around them. These baths were considerably fuller and thus more inviting compared to the tubs you’d see now. The dominant color for tubs is white and it’s also essentially the only way to really go.
With the 60s and 70s came the investigation of bathroom fixtures in beige, browns, pastels, and the like. Despite these bad alternatives, tubs in this age were still really nicely made. Baths in steel appeared while building transferred to comprise lightweights like acrylic, and in layout, these steel baths were even occasionally sculptural and elegant like the casting irons.

Cast iron is generally heralded for its indestructibility when rust might set in. It has a close relative in steel, in fact just minor tweaks in composition would turn one into the other. While steel is heavy, cast iron is more heavy, and bathtubs made of these metals finally well beyond their finish.

Learn more about:refinishing services in San Diego – we cover your needs in La Jolla California.

For just these reasons, you might decide to refinish a bathtub. Any type of bath can be refinished, while those with a timeless clawfoot refinish hope to attain a vintage feel. This post focus on the redo of an alcove bath, undoubtedly the most often installed bathtub.

Tools Materials Ability Level

• Acid-Established commercial cleanser Advanced
Acid etching paste
• Straight razor • Baking soda
Plastic sheeting
Builders paper
• Wire brush • Masking tape
• Auto polisher/buffer •
Polish pads and • Buffing • Sandpaper
• Respirator • Canvas drop cloth
• Rubber gloves • Porcelain repair epoxy or polyester glazing putty
• Rags and towels • Two-Component fiberglass repair putty
Store towels or • Paper • Tack material
• Small mixing trough • Porcelain bonding agent
Peculiarity acrylic urethane OR acrylic aliphatic polyurethane OR white paint and high gloss polyurethane
• Electric paint sprayer • Denatured alcohol
Silicone caulk
Plumbing tools that are •
Tub Refinishing Concerns
As mentioned previously, cast iron and steel baths are incredibly heavy, and you’ll need at least three, a hand, deliver and to remove them to a refinishing works. In case of an alcove tub, one that is “built in,” it’s typically best to approach it while it is still in position.
A refinishing works may often start with a process called “dipping” or stripping the initial finish. After stripped, your bathtub may again have a porcelain enamel implemented before it is ultimately re-fired in a kiln. Similar coatings can be used onsite; stripping, nevertheless, is replaced with other way of prep.

Are You Going To Replace Hardware?

Working under the assumption that once (re)finished, you’ll have a fresh look bathtub. It could be worth it to plan for an update of the bath’s existing drain hardware.
It should be pointed out, too, that the edges are typically the “weakest” part of any finish. In an area always subjected to water, it makes sense at minimum to eliminate the drain ahead of applying your new bathtub finish.

Note: Accessibility to the lower wall cavity supporting the bathtub drain is necessary at the absolute minimum when updating a bathtub’s drain assembly.

Need help with Bathtub refinishing? SB Refinishers provides you with the highest quality services for your needs.

Contemplate How You’ll VentilateBecause, generally, you’ll be working with paints that are airborne and caustic materials, make certain that you have sufficient ventilation as you work. Along with running a built-in bathroom fan, it may also make sense to open a window and utilize cross-ventilation by setting a fan in an opposing doorway. If added concerns remain around your ability to work safely or use paint efficiently, ventilation equipment can also be rented at rental centers or home improvement stores.
Ready the Job

There are numerous methods available for effectively preparing a tub refinish. Whatever the approach you select, take great care in this period. The measures below are common to any job preparation strategy you might choose:
1) Remove Existing Caulk: Remove caulk which should be contacting the bath surface. Begin by cutting both the top and bottom edges of the caulk bead with a utility knife. Follow with a stiff putty knife and end with a straight razor blade. Fully remove. Sweep out or vacuum any debris which will make its way to the bottom of the tub up.

2) Remove OR Mask the Overflow Plate: Plan to replace present bath hardware. The bathtub’s drain continues to be in excellent working order, and also if this isn’t possible, remove. Tubs fitted with linked stoppers can be disconnected or disassembled, but because of uniquenesses in moving parts (especially with antique bathtubs), it may be best to just conceal overflow plates away. Be conscious not to allow linkages to fall back into the overflow should you decide to remove a linked lever or drain.

3) Remove Drain Pop Up, Strainer Assembly, OR Mask: Remove as many of the exposed finished drain components as possible. Mask any finished surface that you just select not to remove. Poke holes or make an X in masking tape as it will be {used later.

4) Give the Bathtub an Industrial Cleaning: Using an acid-based cleanser, spray down the whole bath surface. Allow the product sit for five minutes and make use of a stiff-bristled brush to scrub spots away. Because these cleaners are caustic, wear rubber gloves (or better) and a properly rated respirator. Then let the tub dry.

Mask both the inside of the tub as well as the face (or apron) of the tub as it intersects with toilet walls. Do the same with the tub as it meets the floor. Cut holes in locations where faucet or bathtub spouts handles may appear. Use masking tape prior to spraying.

6) Mask Tub Spout and Faucet Handles: While you may need to time this with the other steps under, wrapping bath spouts and faucets with builder’s paper or additional plastic (cling wrap will work just as well). Alternatively, it may make sense just to remove them.

Prepare the Surface and Make Modest Repairs

Apply an Acid Etching Paste
Use a stiff-bristled four inch stain a scrub brush or brush to use an acid etch designed specially for porcelain. Cover of the tub fully and allow around 15 minutes for this product to do its thing. Wear rubber gloves (or better) and a correctly rated respirator. Wipe dry with shop towels.
Alternatives for Acid Etching

Some will forgo acid etching in favor of employing a bonding agent only. Others might use mechanical means to rough up the bath surface. This really is accomplished by way of using sanding (aka flap) disks fitted to an angle grinder. While this process is somewhat aggressive, most concluding products are self-leveling to the degree that they are going to level out moderately over a “ ” surface that is scarified.
Fixing Bath Surface Imperfections

Spots and grittiness can appear on bathtub surfaces after decades of improper cleaning. Bleach and abrasive cleaners could be detrimental to bath surfaces, themselves working to etch porcelain. Green stains or rust could be addressed using oxalic acid mixed in hot water with talc to form a whiting paste.
Prior to applying a finish dings or processors should additionally be addressed. Blend of two -component fiberglass repair putty and apply to the affected region using a plastic spreader. Allow to dry in line with the product’s directions and sand first with 36-grit sandpaper (the kind used for sanding floors) and then follow with an 80-grit paper to feather out the repair.

Follow with porcelain or polyester glazing to fill in little pockets that could show up in the repaired region, if necessary.

Wipe down the tub with paper towels and follow with a tack cloth.
Optional: For a more thorough cleaning, give the bathtub one final wipe with rapid-evaporating denatured alcohol.

Caution: If acids either weren’t used, simply use or have been effectively neutralized.

Applying Finishes: DIY Strategy

Refinishing Kits
That is a seemingly innumerable array of refinishing kits available from reputable manufacturers. Generally speaking, you’ll find varying amounts of dry times and quality with these products. Do your research before purchasing and understand that cost may advise effectiveness over time. Choose a reputable name and follow all instructions closely. These kits should afford a finish continuing one to five years with appropriate attention.
Assemble Your Own Clothing

The topcoat is implemented using the same sprayer (make certain to wash it thoroughly between steps). Hold the gun about six inches from the surface, when spraying. As you move back and forth, work using long strokes along with a constant movement, overlapping slightly. Play around with a combination of white paint and high-gloss polyurethane. Alternatively, spray or roll on a two-part marine epoxy. This approach should give a finish that’ll continue between 3 and 10 years in case you’ven’t skimped on homework.
Using Finishes: Pro Approach

Professional refinishers are abundant, but be warned: techniques and the products used plus their opinions vary widely.
Master Techniques

(There is much debate online about the favorite sprayer sort for this occupation.n general, pick airless and HVLP over others.) Determined by the merchandise used, each layer should dry 15 to 20 minutes before the next is applied. The final layer should dry for no less than an hour.
A wet sanding with 600/800/1000-grit paper smooths any imperfections. Some use an auto compound buffed into the surface using an auto polisher and annular buffing pads. Hand frequently does additional buffing. Glazing can also be used with a soft cloth to bring up a more dazzling luster.

Tear Down and Reinstall Fixtures
Once the finish has dried to the contact, per product recommendations or after two hours, whichever comes first remove all masking, paper, and plastic from the job site. In case any of the just applied finish begins to pull away with masking, it’s a good idea to work with a utility knife in hand. Work with care over the recently finished surface. Package waste into building bags and dispose of appropriately.
It’s frequently better left to a pro while bathtub refinishing can really be a DIY project. SB Refinishers in San Diego tub refinishing is only one of the jobs that are most practically priced. Costs generally range from $400 to $500 and are often packaged with a guarantee that is significant.
In hiring a professional for this particular occupation the most crucial variable is the individual tech scheduled to do the work. That’s appropriate, don’t always hire an expert based on the name of the company, on their system, or on their procedure, but rather on the actual person you’d need doing your job. These mechanics ought to have the ability to generate a portfolio of work and references. Request it before making a decision, and review it.

san diego bathtub



[su_tabs active=”3″][su_tab title=”Refinishing Videos”][su_tabs active=”3″][su_tab title=”Refinishing Videos”][/su_tab] [/su_tabs][/su_tab] [/su_tabs]

Leave a Reply

Your email address will not be published. Required fields are marked *